7000 lb. Cradle Boat Lift

7000 lb. Cradle Boat Lift
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge
  • Click to enlarge

$1,949.00


Product Information

 

  Boat Lift 7000lb. Kit Includes:
  • 4000lb Gear Unit (7000 lb compounded) Capacity Max, 1 HP Marathon/Leeson TENV (Totally Enclosed Motor), 110 Volt (220 Volt Optional) and In-line GFCI, Lock on Switch, 14' Electrical Wire Motor to Switch(1)

  • Dual pipe supports 24" between collars (2)

  • Bearing Brackets with 4 bolts, nuts (4)

  • 4" Upper Pulleys, Hanger Plates, & Shackles Aluminum Sheave w/Bronze 5/8 Bushing on 5/8 Shaft - LIFETIME WARRANTY 3/8 in. thick x 2 1/2 in. x 12 in. Galvanized Hanger Plates. (4)

  • Compound Pulley Tie Off Bracket W/Shackle (4)

  • 4"Lower Block Pulleys W/Shackle & Grease fitting Aluminum Sheave w/Bronze 5/8 Bushing on 5/8 Stainless Steel Shaft - LIFETIME WARRANTY (4)

  • 6" X 9' , 9'6", 10', or 11' Hot Dipped Galvanized Steel I Beam (2)

  • Chock Brackets 16" with Bolts, Nuts (8)

  • 1/4" Galvanized Cable 75' each piece (2) (This will give 15' from upper pulleys down to all four corners to the cradles with a 10' wide boat slip)(Call us if additional amount of cable is needed)

  • 1/4 in. Galvanized Drop Forged Cable Clamps (12)

  • 1/4" Thimbles (4)

  • 1/2" Shackles (8)

(2 in. ID Schedule 40 Pipe Not Included *Purchase Locally*)

This kit works for a wide variety of boats. All hardware hot dip galvanized. Drive Pipe 2" ID Schedule 40 or 80 (not supplied). Timbers not included. Due to the variety of material thickness used in boat house construction, the bolts etc. are not supplied to connect the kit hardware to the boat house. These can be purchased locally to ensure the correct sizes.

Optional Remote Control - ORDER A TEC 1 REMOTE CONTROL WITH YOUR KIT FOR A SPECIAL PRICE! Comes with hand held remote and pre-wired ready to plug in. Remote operates as a momentary switch, must hold pressure on the up or down button to run the motor. Just click the drop down below to add to the kit!

Motors are TENV Totally Enclosed Non Vented. They are not sealed motors and must be protected from rain and weather.

2 Year Electrical Warranty

FREE SHIPPING ON THIS ITEM (SHIPS BY FREIGHT LINE SIGNATURE REQUIRED)

Cradle must be 1 ft. longer (minimum) than width of boat: Boat slip needs to be a minimum of 1 ft. wider than length of cradle.
Example: Boat 8' wide, minimum cradle 9' & boat slip 10ft. wide

  Free Upgrades Include:
  • 4 in. Block Pulleys in Lieu of 3 in.

  • In-line GFCI in Lieu of In-Plug GFCI

  • Exclusive Formed Mounting Plate is Designed to Improve Strength and Totally Eliminate Deflection Problems Flat Plates Have. The Gears Are Manufactured in the U.S.A With the Best of Materials

  • 2 Year Electrical Warranty

  • 6 Year Gear Plate Warranty
     

FREE SHIPPING ON THIS ITEM

  OPTIONAL: 4000 lb. (7000 lb. when compounded) Maintenance Free Sealed Gear Unit with Cover
  • Lifts Faster than the flat plate gear unit

  • Maintenance Free Sealed Gear Box

  • Permanently Lubed

  • Includes Cover

  • Includes Hanger Brackett


This field is required.
Top