Boat Lift Gear Unit: TENV Motor (Totally Inclosed Motor) - 110v Lock on Switch 14' Electrical Wire Motor to Switch In-line GFCI 6 year w…

   Boat Lift Gear Plate Includes 10" pulley and v-belt. 6 year warranty on gear plate Available in galvanized steel or aluminum FREE SHIPPING ON …

   Boat Lift Motor TENV 110v or 220v: TENV (Totally Enclosed Motor) Wired and Ready To Plug In. Motor Frame 56 Will Fit Most All Flat Plate Gear Units Loc…

   Boat Lift Motor TENV 110v or 220v Motor Only: TENV (Totally Enclosed Motor) Will Fit Most All Flat Plate Gear Units 3/4 hp 110v - 11.4 amps 220v- 6.5 amps …

  Boat Lift Switch Set: Switch & wiring with gfci (Lock or Momentary switch) Lock On (Stays on until you manually turn it off) Momentary ( Runs as long as you hold the lever in t…

  Boat Lift Switch: Lock-on switch (20 Amps) (Stays on until you manually turn it off) Momentary switch (20 Amps) (Runs as long as you hold the lever in the run position) Remove your hand and s…

  Boat Lift Pulley Hanger Kit: 3/8" x 2 1/2" x 12" Pulley Hanger. For Cable up to 5/16" 4" Block Pulley Galvanized, 4" Aluminum Sheave, 5/8" Bronze Bushing, 5/8" Bolt/Nut 2 Ton …

  Boat Lift Shackle: Galvanized 4 included per each order FREE SHIPPING ON THIS ITEM

  Boat Lift Pulley Block: 4” Pulley Block, w/ 4” Aluminum Sheave, Bronze Bushing, Galvanized Plates, 5/8” Bolt. For Cable up to 5/16" (Requires Shackle to attach to Hanger Bracket) …

  Boat Lift Pulley Block w/ Grease Fitting: 4” Pulley Block with Grease Fitting, 4” Aluminum Sheave, Bronze Bushing, Galvanized Plates, 5/8” Stainless Steel Bolt/Nut. For Cable up to 5/16"…

  Boat Lift Rigid Mount Pulley: 4" Aluminum Sheave, 5/8" Bronze Bushing, 5/8" Bolt/Nut, Galvanized. For Cable up to 5/16" Available in 10" & 17" FREE SHIPPING ON THIS…

  Boat Lift Pulley Hanger Angle: 3 x 3 x 12 x 3/16 Galvanized Angle Pulley Hanger (grade 50 steel). 4 plates included per order FREE SHIPPING ON THIS ITEM

  Boat Lift Pulley Hanger Flat Plate: 3/8 x 2 1/2 x 12 Galvanized Flat Plate Pulley Hanger. 4 plates included per order FREE SHIPPING ON THIS ITEM

  Boat Lift Slings (Deluxe): 5/8 Galvanized End Hardware Sling Basket Rated for 8400 lbs. each sling  Lead sewn in on bottom of sling in two places in pockets …

  Boat Lift Dual Pipe Support: 2 L Hanger Brackets and 2 Pipe Support Collars With Grease Fittings Galvanized, For 2" ID Pipe 17" Wrapping Area Center Drive On…

  Boat Lift V Pipe Support: 3/8" Steel Flat Plate Galvanized Grease Fitting Works For 2" Drive Pipe. FREE SHIPPING ON THIS ITEM

  Boat Lift Cable Replacement: All cable replacements are 7x19. Includes 12 galvanized drop forged cable clamps and 4 thimbles. Available in both Galvanized and Stainless 1/4" a…

  Boat Lift Cable Weights: 2 piece bolt together cast iron cable weights (4 complete weights with bolts per order) Due To Casting, Actual Weights May Very Slightly. Appearance may vary from pictu…

  Boat Lift Chock 16" 16" Galvanized Chock W/Bolts (for 5" or 6" tall I beams) (longer bolts may be required than what is supplied. Purchase locally depending on your beam size.) Includes 4 sets…

  Boat Lift Cradle Guide Post:  Cradle Guide Post with hardware Galvanized For I Beam with a Maximum Flange Width of 4 inches between bolts. 2 in. PVC will slip over the 1 1/…

  Boat Lift Gear Unit Cover: 2 Piece Dark Grey Covers Front & Back of Gear Unit. FREE SHIPPING ON THIS ITEM

  Boat Lift Remote Control Unit: All new remote control units now come with a new key chain pendant hand held transmitter and super powerful radio receiver. This new combination allows the remote controls to ope…

  Boat Lift Remote Control Replacement: Replacement or Extra Key Chain Handheld Remote. Easily Programmable. Replacement for the Tec Remote Systems only. PLEASE CALL BEFORE PURCHASING…

  Boat Lift Pontoon Chock: Lifts From The Floor Of Your Boat, Keeping Stress Off The Pontoons. For 4 or 5 inch High Standard I Beam and a Maximum Flange Width of 4 inches between bolts. For high…

  Boat Lift Cradle Beams With Cable Tie Off Eye: 4" x 9' Bottom Beams 3,000lb Max Per Pair 5" x 8' Bottom Beams 6,000lb Max Per Pair 5" x 8'6" Bottom Beams 6,000lb Max Per Pair …

  Boat Lift Pontoon Chock: Will fit I beam 5" no wider than 4" on the flange Choose Between 4 or 6 Chocks Per Order (Each set includes brackets) Always check with the pontoon b…

  Boat Lift Pillow Block Bearings: For 2" ID Pipe & Hanger FREE SHIPPING ON THIS ITEM

  Boat Lift Sealed Bearing With Hanger: Sealed Bearing With Hanger Designed For Downward Pull Only. As Used In Pairs (As Shown On the 10,000 Cradle Lift Kit) Uses 1 1/2" ID …

  Boat Lift V-Belt: V Belt Fits flat plate gear units with 2" pulley on motor & 10' pulley on worm gear shaft FREE SHIPPING ON THIS ITEM

  Boat Lift V-Belt Pulley: 10" V Belt pulley with 3/4 bore for flat plate gear units FREE SHIPPING ON THIS ITEM

  Boat Lift GFCI: 110v Black 220v Yellow FREE SHIPPING ON THIS ITEM

  Boat Lift 2" Heavy Duty V belt Pulley: 2" Heavy Duty V belt Pulley with double set screws for 5/8" motor shaft. These HD pulleys use double set screws for more secure attachment to the motor sh…

  Ladder: 5 Step Retractable or Stationary Ladder 61" Tall to Mounting Bars 17" Wide Step 12" Between Steps 450 lb Weight Limit …

   Boat Lift ALUMINUM Motor TENV 110v or 220v: TENV (Totally Enclosed Motor) Wired and Ready To Plug In. or Motor only. Motor Frame 56 Will Fit Most All Flat Plate Gear Un…